"RSSI"|"027"|"1"|"1"|"2"||"Return compensated RSSI (in dBm) for current ch"|||
"RCVS1"|"023"|"1"|"1"|"2"||"Receive Contiguous 1-word messages on analog control channel; count errors"|||
"RESTART"|"022"|"1"|"0"|"0"||"Generate a software restart"|||
"SUSPEND"|"036"|"1"|"1"|"1"||"Terminate normal mode and enter test mode"|||
"SBSDY_LCK"|"035"|"1"|"XX"|"1"||"Subsidy activation command"|||
"LONG_STAT"|"015"|"1"|"1"|"9"|16.00|"Display radio status in detailed format"|||
"AUD_LVL"|"005"|"1"|"1"|"1"||"Set audio level"|||
"AUD_LPB"|"004"|"1"|"XX"|"0"||"Enable audio loopback.  P2K sends 1 & 3G sends 2."|||
"PREKEY"|"01F"|"1"|"1"|"0"||"Control of prekey power supply to RF section"|||
"STELEM"|"02F"|"1"|"XX"|"1"||"Program element to NVM"|||
"SIGTONE"|"02E"|"1"|"1"|"0"||"Enable/disable signalling tone"|||
"MSG_RT"|"034"|"1"|"321"|"1"||"Configure message routing (task/bottom connector)"|||
"TST_DISP"|"037"|"1"|"XX"|"YY"||"Place a test pattern in the display"|||
"RQ"|"026"|"1"|"XX"|"YY"||"Request various data/status"|||
"MEMACS"|"016"|"1"|"XX"|"YY"||"Read/write memory access to MCU/DSP"|||
"DTMF"|"00B"|"1"|"2"|"0"||"Generate/disable DTMF tones"|||
"PWR_OFF"|"01E"|"1"|"0"|"0"||"Power down the phone"|||
"PHASE"|"01D"|"1"|"XX"|"YY"||"Set a phasing parameter in HW/SW; program to NVM"|||
"RTCC"|"029"|"1"|"7"|"6"||"Set real time clock"|||
"SCMP"|"901"|"1"|"3"|"0"||"Start Simple Camp"|||
"COMPD"|"009"|"1"|"1"|"0"||"Enable/disable compander"|||
"AUD_CTRL"|"003"|"1"|"1"|"0"||"Control various audio functions; enable/disable vibrator"|||
"RDWR_SPI"|"021"|"1"|"XX"|"YY"||"Generic read/write to SPI bus"|||
"RDELEM"|"020"|"1"|"8"|"YY"||"Read element in NVM"|||
"CARRIER"|"007"|"1"|"1"|"1"||"Enable/disable carrier"|||
"MSG_INJ"|"033"|"1"|"XX"|"1"||"Inject message to specific task or message queue"|||
"VERSION"|"039"|"1"|"2"|"YY"||"Get version of selected phone element (DSP, etc)"|||
"WSTS"|"03A"|"1"|"1"|"2"||"Receive contiguous 1-word msgs on analog ctrl channel; count sync sequences"|||
"AUD_PATH"|"006"|"1"|"2"|"0"||"Change audio path"|||
"COMMIT"|"B0C"|"1"|"5"|"1"||"Used to commit scratchpad changes to active memory"|||
"CPY_ACTIVE"|"B0D"|"1"|"2"|"1"||"Copies the active memory to scratchpad memory"|||
"INIT"|"011"|"1"|"0"|"0"||"Initialize radio to known states to be determined"|||
"KEYS"|"013"|"1"|"XX"|"2"||"Perform key strokes"|||
"INVM"|"012"|"1"|"1"|"0"|40.00|"Initialize the non-volatile memory parameters"|||
"TDMA_ON"|"B06"|"1"|"2"|"0"||"Synchronize to forward traffic channel "|||
"TDMA_INFO"|"B05"|"1"|"XX"|"YY"||"Pass TDMA data to TDMA stack"|||
"FLASH"|"00D"|"1"|"0"|"0"||"Put the phone in a mode suitable for flashing"|||
"HDW"|"00F"|"1"|"1"|"0"||"General hardware control"|||
"AUD_TN_LST"|"000"|"1"|"XX"|"0"||"Start or Stop audio tones predefined by the Audio Manager.  P2K sends 3 & 3G sends 1."|||
"CP_MODE"|"00A"|"1"|"1"|"1"||"Select radio call processing mode"|||
"DIGTS"|"B04"|"1"|"1"|"0"||"Switch to DTC mode"|||
"SET_LNA"|"02C"|"1"|"1"|"0"||"Set the Low Noise Amplifier gain control, CDMA only"|||
"SET_RF_PWR"|"02D"|"1"|"1"|"0"||"Set RF power attenuation"|||
"CDATA"|"008"|"1"|"7"|"0"||"Tx continuous data on a channel"|||
"AD_CONV"|"001"|"1"|"2"|"YY"||"Return result of A/D conversion on specified line"|||
"LOAD_SYN"|"014"|"1"|"3"|"0"||"Load channel into synthesizer"|||
"AUTOCYCLE"|"002"|"1"|"1"|"0"||"Simulates product operations by enabling/disabling phone functions."|||
"PARM"|"030"|"1"|"XX"|"YY"|||||
"SMARTCARD"|"03C"|"1"|"XX"|"YY"||"Read/Write From/To SIM card"|||
"WRITE_DA"|"03B"|"1"|"XX"|"0"||"Write to D to A converter"|||
"KEY_PRESS"|"045"|"1"|"2"|"2"||"Performs a key press/releaes events."|||
"GPRS_LPB"|"903"|"1"|"18"|"0"||"GPRS Loopback mode."|||
"PING"|"FFF"|"1"|"0"|"0"||"Test test command connection."|||
"ICACS"|"046"|"1"|"XX"|"YY"||"Peforms key press/ release event"|||
"PA_FDBACK"|"B08"|"1"|"0"|"2"||"Report a power measurement from Tx Output power detection ckt"|||
"TDMA_CFG"|"B09"|"1"|"31"|"0"||"Configure the DSP into different test settings"|||
"IR_STATUS"|"B0A"|"1"|"1"|"8"||"Configures and retrieves IR scan parameters"|||
"LEDS"|"03E"|"1"|"XX"|"0"||"Handles the LEDS on the display."|||
"IRDA"|"040"|"1"|"3"|"1"||"Enable\Disable the IRDA port.  P2K sends 1 & 3G sends 3."|||
"KEY_TEST"|"03F"|"1"|"0"|"2"||"Returns the latest key pressed."|||
"GPIO_TEST"|"041"|"1"|"XX"|"YY"||"Allows access over the various GPIO ports and pins.  P2K uses 8 & 2, 3G uses 13 & 4."|||
"BT"|"042"|"1"|"XX"|"YY"||"Passes data to the Bluetooth Test Control Interface"|||
"TX_PWR_DET"|"B0B"|"1"|"1"|"0"|||||
"FLIP"|"043"|"1"|"1"|"1"||"Sets/Retrieves the state of the flip."|||
"AUD_TN_GEN"|"044"|"1"|"XX"|"0"||"Enable/Disable a generated tone. P2K sends 13 & 3G sends 14."|||
"TLPB"|"902"|"1"|"4"|"0"||"Starts / Stops TCH loopback"|||
"ERS_PANIC"|"00C"|"1"|"0"|"0"||"Erases panic information in flash memory"|||
"GET_PANIC"|"00E"|"1"|"4"|"YY"||"Allows to read the information stored in the panic sector in NVM."|||
"EGPM"|"904"|"1"|"1"|"1"||"Enables/Disables handovers from the GSM band to the PCS band in GSM/PCS phones."|||
"RCVS2"|"024"|"1"|"3"|"24"||"Receive contiguous 1 word messages on ACC for the specified number of frames."|||
"XUPID"|"038"|"1"|"5"|"6"||"Used to get/set Extended Universal Platform Identifier in the flash boot block."|||
"SSI_LPB"|"048"|"1"|"5"|"0"||"Loops back the SAP SSI lines"|||
"CEM_TEST"|"049"|"1"|"1"|"2"||"Allows for connectivity testing of CE-Module bus pins that can't be checked via the GPIO_TEST command."|||
"PROT"|"050"|"1"|"1"|"2"||"Command allows technology selection.  (either GSM or TDMA)"|||
"SAT"|"02B"|"1"|"1"|"0"||"Enable/disable SAT transponding"|||
"GPRS_SEND"|"905"|"1"|"6"|"0"||"Initiates mobile originated data from RLC in the GPRS stack."|||
"FSAC"|"04A"|"1"|"XX"|"YY"|40.00|"Activates different file system requests to and from phone."|||
"MDI"|"017"|"1"|"XX"|"YY"||"Builds MDI message and sends it to DSP."|||
"WR_PBK"|"04B"|"1"|"XX"|"1"||"Stores phonebook record in NVM."|||
"MEMORY"|"051"|"1"|"3"|"YY"||"Returns information about alocated memory (LCA only)."|||
"CARRIER_SYN_ATTN"|"052"|"1"|"5"|"1"||"Combination of CARRIER, LOAD_SYN, and SET_RF_PWR."|||
"HIBERNATE"|"053"|"1"|"0"|"0"||"Powers the phone off using the battery hibernate machanism."|||
"GENERIC_DSP"|"C00"|"1"|"XX"|"YY"||"Generic DSP command."|||
"RDWR_UART"|"C01"|"1"|"10"|"2"||"Read/Write UART."|||
"WSCMP"|"C02"|"1"|"3"|"3"||"WCDMA Simple CAMP."|||
"RDWR_DSP_SPI"|"C03"|"1"|"XX"|"YY"||"Read/Write DSP SPI bus devices."|||
"DSP_SPI_TRIG_CONFIG"|"C04"|"1"|"6"|"0"||"DSP SPI Trigger Configure."|||
"L1T_TOLS"|"C05"|"1"|"6"|"0"||"L1 Timer - Override L1 Signals."|||
"L1T_TFTS"|"C06"|"1"|"XX"|"1"||"L1 Timer - Frame Table Select."|||
"L1T_THEG"|"C07"|"1"|"2"|"0"||"L1 Timer - Halt Event Generator."|||
"L1T_TWRC"|"C08"|"1"|"8"|"0"||"L1 Timer - Write Register Command."|||
"L1T_TRRC"|"C09"|"1"|"4"|"2"||"L1 Timer - Read Register Command."|||
"L1T_TCCT"|"C0A"|"1"|"6"|"0"||"L1 Timer - Change Channel Timing."|||
"WLOAD_SYN"|"C0B"|"1"|"4"|"0"||"WCDMA Load Synthesizer."|||
"RSSI_RSCP"|"C0D"|"1"|"1"|"YY"||"Receive Signal Strength Indicator, Receive Signal Code Power."|||
"W_CARRIER"|"C0E"|"1"|"12"|"0"||"WCDMA Carrier."|||
"W_PHASE"|"C0F"|"1"|"XX"|"YY"||"WCDMA Phase."|||
"WPC_VAR"|"C10"|"1"|"XX"|"YY"||"WCDMA Power Control Variables."|||
"WPC_DTAR"|"C11"|"1"|"3"|"0"||"WCDMA Power Control RF Detect Target."|||
"WPC_TPC"|"C12"|"1"|"3"|"0"||"WCDMA Power Control TPC Patterns."|||
"RDWR_HARM"|"C13"|"1"|"XX"|"YY"||"Read/Write Harmony Lite."|||
"RQBER"|"C14"|"1"|"0"|"12"||"Request PN9 Sequence Bit Error Rate."|||
"AUD_SAMP"|"C15"|"1"|"2"|"YY"||"Audio Sample."|||
"WOPCHAN"|"C16"|"1"|"8"|"3"||"WCDMA Open Channel."|||
"GPS"|"C17"|"1"|"XX"|"YY"||"GPS Test Command."|||
"KJAVA"|"054"|"1"|"XX"|"YY"|90.00|"kJava Test Commands."|||
"SUSPEND_COMP"|"C18"|"1"|"XX"|"YY"||"Suspend Component."|||
"TOUCH_SCREEN"|"C19"|"1"|"XX"|"YY"||"Touch Screen Interface Parameters."|||
"TST_MMC"|"C1B"|"1"|"XX"|"YY"||"Test Multi-Media Card."|||
"WUPD_COMP"|"C1C"|"1"|"4"|"YY"||"Update Compensated Values."|||
"CALL"|"04D"|"1"|"1"|"2"||"Make a test voice call in the factory."|||
"PU_TSTMODE"|"04C"|"1"|"1"|"1"||"Gets powerup mode of phone or sets next powerup mode."|||
"CAMERA"|"C1A"|"1"|"XX"|"YY"||"Test Camera HW and Driver."|||
"BAUD_RATE"|"C1D"|"1"|"2"|"4"||"Configure UART baud rate."|||
"TXBD"|"906"|"1"|"10"|"1"||"Modifies TX phasing param's during burst xmit."|||
"EFSAC"|"060"|"1"|"XX"|"YY"||"Activates different file system requests to and from the phone."|||
"TRAC_ACTIVE"|"055"|"1"|"1"|"1"||"Changes Tracfone state."|||
"IS_FR"|"056"|"1"|"1"|"2"||"Future Ready."|||
"SWDL"|"057"|"1"|"1"|"YY"|30.00|"SW Download file creation for backup."|||
"SWUL"|"058"|"1"|"XX"|"YY"|30.00|"SW Download file restore."|||
"DIP_SWITCH"|"D00"|"1"|"2"|"2"||"Read a set of SW flags."|||
"READ_ADC"|"D01"|"1"|"1"|"2"||"Read Specified ADC."|||
"GPS_CHECK_AGC"|"D02"|"1"|"1"|"3"||"Read GPS AGC."|||
"CW_SIGNAL"|"D03"|"1"|"1"|"1"||"Continuous wave generation from interleaver."|||
"WLONG_STAT"|"C24"|"1"|"1"|"YY"||"Get WCDMA long status."|||
"TST_CAMERA"|"061"|"1"|"XX"|"YY"||"General purpose Camera command."|||
"OCD"|"C23"|"1"|"1"|"2"||"On Chip Debugger."|||
"RDWR_IO"|"C25"|"1"|"4"|"YY"||"GPIO_TEST abstraction."|||
"RD_IC"|"C21"|"1"|"1"|"16"||"Read Integrated Circuit ID."|||
"PDLOG"|"C20"|"1"|"1"|"76"||"Power Down LOG."|||
"AUD_TN_TEST"|"059"|"1"|"XX"|"1"||"Play list of phased frequencies."|||
"ALERT"|"090"|"1"|"1"|"1"||"Generates a tone."|||
"HS_LPB"|"091"|"1"|"1"|"1"||"Enable headset loopback function1."|||
"AUD_PH_LPB"|"092"|"1"|"1"|"1"||"Enable headset loopback function2."|||
"ALT_STOP_AUD_PH_LPB"|"093"|"1"|"1"|"1"||"Disables tone and enables loopback."|||
"VIB_STOP_ALERT"|"094"|"1"|"1"|"1"||"Disables vibrator and tone."|||
"CIT_ELEM"|"095"|"1"|"XX"|"1"||"Stamps status of CIT test."|||